现在我直接选的7500 V5的ubootsuperwrt_boot_tl_wdr7500_v5_20170912.img

cloudq
帖子: 46
注册: 周五 3月 18, 2016 8:43 am

现在我直接选的7500 V5的ubootsuperwrt_boot_tl_wdr7500_v5_20170912.img

帖子cloudq » 周六 9月 16, 2017 7:10 pm

现在我直接选的7500 V5的ubootsuperwrt_boot_tl_wdr7500_v5_20170912.img 输入后,结果和我自己定制那个一样(我自己定制那个我记得最早还是好用的,好久没刷了)


SuperWRT Boot 1.3.6-gf7fef81e-dirty (Sep 12 2017 - 16:14:14)

QCA955x - Scorpion 1.0

DRAM: 128 MB
Flash: 16 MB (12018)
Using default environment

Frequency: CPU 720MHz / RAM 600MHz / AHB 240MHz
Bootstrap Config: 0x00021e5c
SuperWRT Board Info(0x9f01c000):
TP WDR7500 v5.0/terra@superwrt.com/2016-01-29
Auto extend mtd parts size to 16M!
WLAN0 info: cal:0x9f01e000, mac:0x9f01d80d
Device UID: none
GPIO: reset(16/L), system(14/L)
In: serial
Out: serial
Err: serial
Net: (02:54:65:72:72:61) S17phy S17 [RGMII CALED: XMII=0x00000000 ETH_CFG=0x0003c041] eth0, eth1
Set 0x18116290 = 0x458a214f
Hit 'c' or 'Ctrl+c' to stop autoboot: 1
Net Command waiting: 2
Try eth1 first.
dup 1 speed 1000

config: Config magic check error!
config2: Config magic check error!
## Booting image at 9f800000 ...
Image Name: SuperWrt qca/qca9k/std
Created: 2017-09-12 8:13:14 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1301030 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f800178 ...OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.18.47 (terra@localhost.localdomain) (gcc version 4.8.3 (SuperWrt/Linaro GCC 4.8-2014.04 r44747) ) #1 Tue Sep 12 16:11:26 CST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:112k(uboot),4k(SBI),12k(CAL),64k(elog),128k(custom),128k(config),128k(config2),7488k(udata),64k(DTB),64k(CAL2),8192k(firmware) mem=128M sbi=0x9f01c000 rootfstype=squashfs,jffs2 init=/sbin/init noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125428K/131072K available (3103K kernel code, 172K rwdata, 420K rodata, 200K init, 171K bss, 5644K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
[ 0.028000] pid_max: default: 32768 minimum: 301
[ 0.032000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.036000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] NET: Registered protocol family 16
[ 0.044000] MIPS: machine is SuperWRT
[ 0.048000] registering PCI controller with io_map_base unset
[ 0.052000] ar724x-pci ar724x-pci.1: PCIe link is down
[ 0.056000] registering PCI controller with io_map_base unset
[ 0.484000] SCSI subsystem initialized
[ 0.488000] usbcore: registered new interface driver usbfs
[ 0.492000] usbcore: registered new interface driver hub
[ 0.496000] usbcore: registered new device driver usb
[ 0.500000] PCI host bridge to bus 0000:00
[ 0.504000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.508000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.512000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.516000] pci 0000:00:00.0: invalid calibration data
[ 0.520000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.524000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.528000] PCI host bridge to bus 0000:01
[ 0.532000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.536000] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.540000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.544000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.548000] Switched to clocksource MIPS
[ 0.552000] NET: Registered protocol family 2
[ 0.556000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.564000] TCP bind hash table entries: 1024 (order: 2, 20480 bytes)
[ 0.572000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.580000] TCP: reno registered
[ 0.584000] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.588000] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.596000] NET: Registered protocol family 1
[ 0.604000] futex hash table entries: 256 (order: 0, 7168 bytes)
[ 0.628000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.632000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.644000] msgmni has been set to 244
[ 0.652000] io scheduler noop registered
[ 0.656000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.668000] console [ttyS0] disabled
[ 0.692000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.704000] console [ttyS0] enabled
[ 0.704000] console [ttyS0] enabled
[ 0.708000] bootconsole [early0] disabled
[ 0.708000] bootconsole [early0] disabled
[ 0.720000] m25p80 spi0.0: found s25fl129p1, expected m25p80
[ 0.724000] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
[ 0.732000] 11 cmdlinepart partitions found on MTD device spi0.0
[ 0.736000] Creating 11 MTD partitions on "spi0.0":
[ 0.740000] 0x000000000000-0x00000001c000 : "uboot"
[ 0.748000] 0x00000001c000-0x00000001d000 : "SBI"
[ 0.752000] 0x00000001d000-0x000000020000 : "CAL"
[ 0.760000] 0x000000020000-0x000000030000 : "elog"
[ 0.764000] mtdoops: MTD partition 3 not big enough for mtdoops
[ 0.768000] 0x000000030000-0x000000050000 : "custom"
[ 0.776000] 0x000000050000-0x000000070000 : "config"
[ 0.780000] 0x000000070000-0x000000090000 : "config2"
[ 0.788000] 0x000000090000-0x0000007e0000 : "udata"
[ 0.792000] 0x0000007e0000-0x0000007f0000 : "DTB"
[ 0.800000] 0x0000007f0000-0x000000800000 : "CAL2"
[ 0.804000] 0x000000800000-0x000001000000 : "firmware"
[ 0.808000] Split rootfs Part: off:0x93dba0 len:0x6c2460
[ 0.816000] 0x00000093dba0-0x000001000000 : "rootfs"
[ 0.820000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.828000] 0x000000b70000-0x000001000000 : "rootfs_data"
[ 0.832000] mtd: device 11 (rootfs) set to be root filesystem
[ 0.852000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 0.944000] libphy: ag71xx_mdio: probed. phys=0x01ff001f
[ 1.520000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.532000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.104000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.108000] PPP generic driver version 2.4.2
[ 2.116000] PPP MPPE Compression module registered
[ 2.120000] NET: Registered protocol family 24
[ 2.124000] PPTP driver version 0.8.5
[ 2.128000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.136000] ehci-pci: EHCI PCI platform driver
[ 2.140000] ehci-platform: EHCI generic platform driver
[ 2.144000] ehci-platform ehci-platform.0: EHCI Host Controller
[ 2.152000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 2.160000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 2.168000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 2.188000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 2.192000] hub 1-0:1.0: USB hub found
[ 2.196000] hub 1-0:1.0: 1 port detected
[ 2.200000] ehci-platform ehci-platform.1: EHCI Host Controller
[ 2.208000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 2.220000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 2.224000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 2.244000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 2.248000] hub 2-0:1.0: USB hub found
[ 2.252000] hub 2-0:1.0: 1 port detected
[ 2.256000] usbcore: registered new interface driver usblp
[ 2.264000] usbcore: registered new interface driver usb-storage
[ 2.268000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 2.280000] Netfilter messages via NETLINK v0.30.
[ 2.284000] nf_conntrack version 0.5.0 (1959 buckets, 7836 max)
[ 2.292000] xt_time: kernel timezone is -0000
[ 2.296000] gre: GRE over IPv4 demultiplexor driver
[ 2.300000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.304000] TCP: cubic registered
[ 2.308000] NET: Registered protocol family 10
[ 2.316000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.320000] NET: Registered protocol family 17
[ 2.328000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.340000] Ebtables v2.0 registered
[ 2.344000] 8021q: 802.1Q VLAN Support v1.8
[ 2.352000] VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
[ 2.360000] Freeing unused kernel memory: 200K (803fe000 - 80430000)
init started: BusyBox v1.22.1 (2017-09-12 16:05:49 CST)
starting pid 369, tty '': 'sh /etc/init.d/rcS S start'
mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
mount: mounting nodev on /sys/kernel/debug failed: No such file or directory
Fri Jan 1 00:00:00 UTC 2010
Try backup config
[ 4.416000] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 4.424000] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 4.816000] swd: module license 'Proprietary' taints kernel.
[ 4.820000] Disabling lock debugging due to kernel taint
[ 4.828000] SuperWRT Network Engine installed!SWD sbi: No valid hw sign.
[ 5.100000] ath: phy0: Unable to initialize hardware; initialization status: -5
[ 5.108000] ath9k qca955x_wmac: failed to initialize device
[ 5.112000] ath9k: probe of qca955x_wmac failed with error -5
[ 5.248000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 5.252000] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 5.448000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 5.460000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 5.672000] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[ 5.680000] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 1 testmode 0
[ 5.696000] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.70.59-2 api 5 features no-p2p,raw-mode,mfp crc32 4159f498
[ 5.744000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 5.756000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board.bin failed with error -2
[ 5.768000] ath10k_pci 0000:00:00.0: failed to fetch board data
[ 5.772000] ath10k_pci 0000:00:00.0: failed to fetch board file: -2
[ 5.780000] ath10k_pci 0000:00:00.0: could not probe fw (-2)
[ 5.932000] random: svld urandom read with 22 bits of entropy available

回到 “路由器系统”