刷的是superwrt-qca-qca9k-std_v0.6.3_20170919.spkg
SuperWRT Boot 1.2.5-g76975354-dirty (Nov 29 2016 - 15:22:33)
QCA953x - Honey Bee 2.0
DRAM: 64 MB
Flash: 8 MB (c84017)
Using default environment
Frequency: CPU 650MHz / RAM 597MHz / AHB 216MHz
Bootstrap Config: 0x00000000
In: serial
Out: serial
Err: serial
Net: (02:54:65:72:72:61) S27phy S27 eth0, eth1
Net Command waiting: 2
eth0 link down
dup 1 speed 1000
Hit 'c' to stop autoboot: 0
config: Config magic check error!
config2: Config magic check error!
## Booting image at 9f020000 ...
Image Name: SuperWrt qca/qca9k/std
Created: 2017-09-19 9:04:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1301237 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f020178 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.47 (terra@localhost.localdomain) (gcc version 4.8.3 (SuperWrt/Linaro GCC 4.8-2014.04 r44747) ) #1 Tue Sep 19 17:02:28 CST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:112k(uboot),16k(SBI),7680k(firmware),64k(elog),64k(config),64k(config2),64k(custom),64k(DTB),64k(CAL) mem=64M rootfstype=squashfs,jffs2 init=/sbin/init noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60452K/65536K available (3103K kernel code, 194K rwdata, 420K rodata, 176K init, 171K bss, 5084K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:650.000MHz, DDR:597.851MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 431.10 BogoMIPS (lpj=862208)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] NET: Registered protocol family 16
[ 0.048000] MIPS: machine is SuperWRT
[ 0.052000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 8006d61c, ra == 804059f0
[ 0.056000] Oops[#1]:
[ 0.056000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.47 #1
[ 0.056000] task: 83828000 ti: 83830000 task.ti: 83830000
[ 0.056000] $ 0 : 00000000 00000072 0000d357 00000000
[ 0.056000] $ 4 : 00000000 00000000 00000000 801ebf7c
[ 0.056000] $ 8 : 00000001 00000165 8385f280 706c6174
[ 0.056000] $12 : ffffff80 00000007 00000000 00000000
[ 0.056000] $16 : 804059c8 80422730 00000000 00000049
[ 0.056000] $20 : 803d0000 80422700 80404230 80430000
[ 0.056000] $24 : 00000002 801e7f74
[ 0.056000] $28 : 83830000 83831cf0 00000000 804059f0
[ 0.056000] Hi : 00000000
[ 0.056000] Lo : 00000000
[ 0.056000] epc : 8006d61c 0x8006d61c
[ 0.056000] Not tainted
[ 0.056000] ra : 804059f0 0x804059f0
[ 0.056000] Status: 1000c403 KERNEL EXL IE
[ 0.056000] Cause : 00800008
[ 0.056000] BadVA : 00000000
[ 0.056000] PrId : 00019374 (MIPS 24Kc)
[ 0.056000] Modules linked in:
[ 0.056000] Process swapper (pid: 1, threadinfo=83830000, task=83828000, tls=00000000)
[ 0.056000] Stack : 83831d48 8006a8c8 83831d48 803e5288 8385d144 00000000 00000000 80366ee4
00000000 803f0000 00000000 00000001 00000000 803e5288 801ebf7c 803f1938
00000000 803e52bc 00000001 80069190 80430000 80069590 83804498 8380444c
803f18d8 803e5288 803f1938 00000000 00000000 83848400 8385dfa0 801e7f5c
83848400 8385dfa0 803e5290 803f1938 00000000 80366b7c 803e5288 8006a8c8
...
[ 0.056000] Call Trace:[<8006a8c8>] 0x8006a8c8
[ 0.056000] [<80366ee4>] 0x80366ee4
[ 0.056000] [<801ebf7c>] 0x801ebf7c
[ 0.056000] [<80069190>] 0x80069190
[ 0.056000] [<80069590>] 0x80069590
[ 0.056000] [<801e7f5c>] 0x801e7f5c
[ 0.056000] [<80366b7c>] 0x80366b7c
[ 0.056000] [<8006a8c8>] 0x8006a8c8
[ 0.056000] [<801e95fc>] 0x801e95fc
[ 0.056000] [<801ed400>] 0x801ed400
[ 0.056000] [<804059c8>] 0x804059c8
[ 0.056000] [<804059c8>] 0x804059c8
[ 0.056000] [<80404230>] 0x80404230
[ 0.056000] [<804059f0>] 0x804059f0
[ 0.056000] [<80414bbc>] 0x80414bbc
[ 0.056000] [<80418788>] 0x80418788
[ 0.056000] [<8006b0ec>] 0x8006b0ec
[ 0.056000] [<80420000>] 0x80420000
[ 0.056000] [<8006a880>] 0x8006a880
[ 0.056000] [<80098930>] 0x80098930
[ 0.056000] [<800a4a14>] 0x800a4a14
[ 0.056000] [<8006a8e8>] 0x8006a8e8
[ 0.056000] [<80404bcc>] 0x80404bcc
[ 0.056000] [<80404230>] 0x80404230
[ 0.056000] [<8009c15c>] 0x8009c15c
[ 0.056000] [<80065208>] 0x80065208
[ 0.056000] [<80065218>] 0x80065218
[ 0.056000] [<80065208>] 0x80065208
[ 0.056000] [<80060878>] 0x80060878
[ 0.056000]
[ 0.056000]
Code: afb1011c afb00118 00809021 <94840000> 3403d357 afa000f8 a7a000fc afa000f0 a7a000f4
[ 0.060000] ---[ end trace b90940bc4ac93c5e ]---
[ 0.064000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.064000]
[ 0.064000] Rebooting in 3 seconds..
wdr6300 v6 刷完 firmware不停重启
Re: wdr6300 v6 刷完 firmware不停重启
lygemail 写了:刷的是superwrt-qca-qca9k-std_v0.6.3_20170919.spkg
SuperWRT Boot 1.2.5-g76975354-dirty (Nov 29 2016 - 15:22:33)
QCA953x - Honey Bee 2.0
DRAM: 64 MB
Flash: 8 MB (c84017)
Using default environment
Frequency: CPU 650MHz / RAM 597MHz / AHB 216MHz
Bootstrap Config: 0x00000000
In: serial
Out: serial
Err: serial
Net: (02:54:65:72:72:61) S27phy S27 eth0, eth1
Net Command waiting: 2
eth0 link down
dup 1 speed 1000
Hit 'c' to stop autoboot: 0
config: Config magic check error!
config2: Config magic check error!
## Booting image at 9f020000 ...
Image Name: SuperWrt qca/qca9k/std
Created: 2017-09-19 9:04:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1301237 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f020178 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.47 (terra@localhost.localdomain) (gcc version 4.8.3 (SuperWrt/Linaro GCC 4.8-2014.04 r44747) ) #1 Tue Sep 19 17:02:28 CST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:112k(uboot),16k(SBI),7680k(firmware),64k(elog),64k(config),64k(config2),64k(custom),64k(DTB),64k(CAL) mem=64M rootfstype=squashfs,jffs2 init=/sbin/init noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60452K/65536K available (3103K kernel code, 194K rwdata, 420K rodata, 176K init, 171K bss, 5084K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:650.000MHz, DDR:597.851MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 431.10 BogoMIPS (lpj=862208)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] NET: Registered protocol family 16
[ 0.048000] MIPS: machine is SuperWRT
[ 0.052000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 8006d61c, ra == 804059f0
[ 0.056000] Oops[#1]:
[ 0.056000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.47 #1
[ 0.056000] task: 83828000 ti: 83830000 task.ti: 83830000
[ 0.056000] $ 0 : 00000000 00000072 0000d357 00000000
[ 0.056000] $ 4 : 00000000 00000000 00000000 801ebf7c
[ 0.056000] $ 8 : 00000001 00000165 8385f280 706c6174
[ 0.056000] $12 : ffffff80 00000007 00000000 00000000
[ 0.056000] $16 : 804059c8 80422730 00000000 00000049
[ 0.056000] $20 : 803d0000 80422700 80404230 80430000
[ 0.056000] $24 : 00000002 801e7f74
[ 0.056000] $28 : 83830000 83831cf0 00000000 804059f0
[ 0.056000] Hi : 00000000
[ 0.056000] Lo : 00000000
[ 0.056000] epc : 8006d61c 0x8006d61c
[ 0.056000] Not tainted
[ 0.056000] ra : 804059f0 0x804059f0
[ 0.056000] Status: 1000c403 KERNEL EXL IE
[ 0.056000] Cause : 00800008
[ 0.056000] BadVA : 00000000
[ 0.056000] PrId : 00019374 (MIPS 24Kc)
[ 0.056000] Modules linked in:
[ 0.056000] Process swapper (pid: 1, threadinfo=83830000, task=83828000, tls=00000000)
[ 0.056000] Stack : 83831d48 8006a8c8 83831d48 803e5288 8385d144 00000000 00000000 80366ee4
00000000 803f0000 00000000 00000001 00000000 803e5288 801ebf7c 803f1938
00000000 803e52bc 00000001 80069190 80430000 80069590 83804498 8380444c
803f18d8 803e5288 803f1938 00000000 00000000 83848400 8385dfa0 801e7f5c
83848400 8385dfa0 803e5290 803f1938 00000000 80366b7c 803e5288 8006a8c8
...
[ 0.056000] Call Trace:[<8006a8c8>] 0x8006a8c8
[ 0.056000] [<80366ee4>] 0x80366ee4
[ 0.056000] [<801ebf7c>] 0x801ebf7c
[ 0.056000] [<80069190>] 0x80069190
[ 0.056000] [<80069590>] 0x80069590
[ 0.056000] [<801e7f5c>] 0x801e7f5c
[ 0.056000] [<80366b7c>] 0x80366b7c
[ 0.056000] [<8006a8c8>] 0x8006a8c8
[ 0.056000] [<801e95fc>] 0x801e95fc
[ 0.056000] [<801ed400>] 0x801ed400
[ 0.056000] [<804059c8>] 0x804059c8
[ 0.056000] [<804059c8>] 0x804059c8
[ 0.056000] [<80404230>] 0x80404230
[ 0.056000] [<804059f0>] 0x804059f0
[ 0.056000] [<80414bbc>] 0x80414bbc
[ 0.056000] [<80418788>] 0x80418788
[ 0.056000] [<8006b0ec>] 0x8006b0ec
[ 0.056000] [<80420000>] 0x80420000
[ 0.056000] [<8006a880>] 0x8006a880
[ 0.056000] [<80098930>] 0x80098930
[ 0.056000] [<800a4a14>] 0x800a4a14
[ 0.056000] [<8006a8e8>] 0x8006a8e8
[ 0.056000] [<80404bcc>] 0x80404bcc
[ 0.056000] [<80404230>] 0x80404230
[ 0.056000] [<8009c15c>] 0x8009c15c
[ 0.056000] [<80065208>] 0x80065208
[ 0.056000] [<80065218>] 0x80065218
[ 0.056000] [<80065208>] 0x80065208
[ 0.056000] [<80060878>] 0x80060878
[ 0.056000]
[ 0.056000]
Code: afb1011c afb00118 00809021 <94840000> 3403d357 afa000f8 a7a000fc afa000f0 a7a000f4
[ 0.060000] ---[ end trace b90940bc4ac93c5e ]---
[ 0.064000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.064000]
[ 0.064000] Rebooting in 3 seconds..
刷错文件了。不要用不带设备信息的boot。
